Calibre遇到的問題

dreamland

執行calibre時,出現了這個警告:

! J  m; N- B# w6 r8 H) ]7 P, k
Could not connect to socket 9189 on host localhost

* X% i7 C( T  S/ ^: KProbable causes:
9 U0 ^# U. B5 C0 ^: X( v
1: The viewer is not running, or
2: The viewer's server socket is not activated
. k+ n0 H: S+ ^* I# q4 G1 u

2 y7 x" C1 X) O7 }) b6 y8 ]7 y請問有人遇過嗎?

shkao0201

那是因為你的layout tool的port不是使用9189
! |( z3 j8 v( P所以你無法將RVE的資料傳回layout
virtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--->9189

dreamland

原帖由 shkao0201 於 2009-10-29 05:51 PM 發表
5 k/ \4 d  M9 ~: g+ w( T那是因為你的layout tool的port不是使用9189
) _  u6 @0 V$ d; ?. v2 n所以你無法將RVE的資料傳回layout
virtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--- ...

4 z- V0 X& N3 Y# ?5 h  J
8 @" f; }, ^5 X' W
我使用的server port是9189

shkao0201

試試在Calibre RVE視窗中: Setup---Layout Viewer-----LayoutViewer(選other(Virtuoso))**Laker要選這個
" D' @' `+ f6 z: A% Z                                                                                         ----IPC  settings--socket number-----9189

shkao0201

然後你可以試試點Connect是否會出現Success.

shkao0201

Setting Up Communication With a Viewer
If you invoke Calibre Interactive from a layout or schematic viewer, communication between
4 c* x; c0 z) e$ L/ `( H( kthe two applications is set up automatically. If you open a viewer after invoking Calibre
" d/ {# @! o1 c7 r/ k! F. CInteractive, you can set up communication between the two tools through IPC sockets.
( _, E5 c" E) ^9 C" qBy default, Calibre seeks socket 8192, and if that socket is available, connection is automatic.
& k% g" u: k0 ]# g: w& gYou can change the socket address used by following this procedure:
5 q, s- Y* B7 g' n1. Open the viewer.
2. Activate a socket following the instructions described in the user manual for the layout viewer you have opened.
, I8 t' z5 K6 A9 _) ?0 L0 X3. In Calibre Interactive, choose Setup > Layout Viewer…
4. Enter the socket number that you activated in the viewer.
7 o) Z& |4 E- b  T5. Click Connect.
) G! z9 s& D' k. _6 C6. Click OK. The figure shows setup of a layout viewer.

dreamland

原帖由 shkao0201 於 2009-10-29 06:12 PM 發表
# ]' W8 u% n2 B7 HSetting Up Communication With a Viewer
, d( i- K3 a* B7 j1 b* H7 [If you invoke Calibre Interactive from a layout or schematic viewer, communication between
* C4 F8 }+ G5 d' W2 jthe two applications is set up automatically. If you open a viewer a ...

9 t& ~( @2 k- K+ c! ^8 F0 r" q3 r

一樣不行用?

shkao0201

你是試用laker去叫出RVE呢??
它的socket number 有相同嗎?